Living

<< Previous   of   Next >>   ADVERTISEMENT   CONTACT THE HERALD Melanie Munk, Features Editor munk@heraldnet.com   Published: Thursday, November 5, 2009 Refinished light fixtures dress up your home for little money The Carey Brothers The value of a home is enhanced when it appears well-maintained, and refinishing a light fixture is one of the single most cost-effective home improvements you can do. One of our readers recently reported that her two large entry light fixtures looked as though they were ready for light-fixture heaven and that replacement would cost more than $800. She took our advice, and within four evenings (a few hours each sitting) and an investment of $35 in materials and equipment, made her old fixtures look brand new. Even the best light fixtures (made from solid brass) eventually corrode to a point where they completely lose their smooth, shiny finish. Reviving old, tattered brass is easy. Brass is a relatively soft metal, and even the most badly oxidized surface can be polished to its original sheen. The steps are easy. First, disassemble the fixture to its smallest component. This will make working on ornate fixtures much simpler. Even though the brass is tarnished, a thin protective coating (usually clear lacquer) must be completely removed. Use paint remover to do this. Since the clear coating is almost invisible, there won't be much satisfaction in performing this step. However, omitting this step will make the sanding and polishing steps far more difficult. Once the clear protective coating is removed, sandpaper is used to remove the oxidized surface layer of the brass, including any pitting that may exist. Yes, the sandpaper will scratch the surface but a second sanding with a finer grit will bring you one step closer to the polishing phase where metal polish is used to remove all traces of the sandpapering phase and to once again bring the surface to a high sheen. The grade of sandpaper required will depend on how badly corroded the surface is. Eighty-grit should be used for deeply pitted surfaces, 150-grit for moderately pitted surfaces and 200-grit for lightly pitted surfaces. In every case, 400- to 600-grit wet and dry sandpaper dipped in water should be used for the final sanding. Although hand polishing is acceptable, a polishing wheel is faster and easier to use. You don't need to purchase a fancy bench grinder with a bunch of exotic polishing wheels. All that's needed is a common household drill with a polishing pad attachment. It can be mounted in a bench vice or clamped to a workbench or heavy piece of old furniture (the clamp may leave marks). Polishing rouge, in the form of a large crayon or stick, is applied to the polishing pad while it is rotating. The brass surface is held against the spinning pad to remove scratches and buff the yellow metal to a bright, golden sheen. Then, a coat or two of liquid brass polish such as Brasso or Flitz can be used to bring out the final luster of the metal and remove all traces of the polishing rouge. Finally, spray on a new protective coating of clear lacquer or a clear polyurethane paint to seal the shiny brass and protect it against oxidation. It is important not to touch the surface of the brass with bare hands between the polishing and protective coating stages. Wear soft white cotton gloves during and after polishing. The oil in your skin will cause the brass to rapidly discolor. If you aren't careful here you may get the opportunity to see your fingerprints on the surface of the light fixture within a few weeks. Once the clear coating has had a chance to dry, reassemble and remount the fixture. For tips from James and Morris Carey, visit www.onthehouse.com or call the 24/7 listener hot line, 800-737-2474, ext. 59. You can also enter to win one of a pair grand prizes totaling more than $25,000 in value. The Careys are also on KRKO (1380 AM) from 6 to 10 a.m. every Saturday. READER COMMENTS Be the first to comment. You must be a registered user and verify your e-mail address to post comments to blogs or articles on HeraldNet. To register, click here. To read other terms and conditions, click here. Log out

1. Trooper rear-ended by suspected drunk driver north of Tulalip 2. Marysville accident backs up I-5 for miles 3. Democrats split over choice for Snohomish County prosecuting attorney 4. Damage persists after off-roading ban in Reiter Foothills 5. Snohomish County stores dangle discounts to grab shoppers 6. New Age of extra income 7. Thanksgiving tradition flourishes at Everett church 8. Transformed Silvertip 9. Toys that reflect racial diversity haled as ‘about time’ 10. Tips for Christmas-tree buying in Snohomish County 2 - Top 10 Stories Most Talked about 3 - Top 10 Stories Most Emailed

• Ruling in the pool • Holiday Lightings & Santa Sightings • Archbishop Murphy takes title • A season of performing arts • Budget numbers have official fuming • Wildcats move on to 2A semifinals • Holiday Bazaars & Fairs Calendar • Edmonds’ Westgate Chapel serves up hospitality for holiday • Mavericks fall • Boeing will build, flight test and deliver 787s in South Carolina to spe ... • Snohomish County EDC promoting job growth in key industry clusters • $4 million grant to advance brain tumor research has Everett links • Providence medical center construction tops off its 12-story steel frame ... • Tulalip affordable housing project to be financed by KeyBank, Raymond Ja ... • Arlington's Lak of Ink has a growing following for Luke Kooyman's creati ... • Bank of the Northwest formed • Cascade Bank earns $1.6 million