By the middle of last year, an inspector identified eight different points on the bridge that had high-load damage, including some portions in which components were deformed by the impact. Then, last fall, inspectors encountered perhaps the worst damage yet: A tall vehicle traveling northbound had struck the overhead bridge structure, ripping a 3-inch gash in the steel, causing three portions to distort and tearing off surrounding paint, according to images and documents obtained by The Associated Press under public records law.
Even after that, state officials still didn't take precautions to prevent truckers from doing it again.
The AP found that Washington state's Department of Transportation regularly puts detailed warnings on its trucking permits when routes are projected to encounter potentially problematic areas of low clearance. But despite the history of issues on the Skagit River bridge, the state never added warnings to permits for that span.
Federal transportation investigators believe an oversized load struck the Skagit bridge last month, causing a portion of it to collapse into the river and two vehicles with it. Nobody was seriously injured, but the failure has continued to disrupt transportation along the crucial I-5 corridor between Seattle and Vancouver, B.C.
In the permit issued by the Department of Transportation to allow the oversize load across the bridge, the state determined that the route was OK for a load that stood 15 feet, 9 inches tall, even though the outer edges of the bridge had a clearance of less than 15 feet. DOT did add a qualification that the agency does not guarantee the height clearances, and DOT spokesman Travis Phelps said it is the company's responsibility to ensure that the load safely passes.
That permit, however, was much different than another approval given just two days earlier to the same company. In that request, Mullen Trucking sought to bring a large boiler along Interstate 90, with a maximum height of just 14 feet. At 10 points on the route path, the DOT issued a "CAUTION" notice, detailing the height of the overhead clearance and asking the driver to take a different route if the load was within two inches of that level. None of those overhead heights were a problem on that specific permit because they were at least seven inches higher than the load.
Phelps said DOT puts out the caution notifications on some areas that have had clearance problems in the past -- but that not every clearance height is noted. The state didn't consider the Skagit bridge to be particularly problematic.
"We don't put every bridge that's been struck onto a permit," he said.
The issues over the Skagit first started appearing in handwritten inspection notes in 1979 when an inspector noted what he deemed "minor dings" in various components, according to records reviewed by AP. A 1985 inspection specifically described "high load dings" on the first overhanging portions of the bridge that vehicles would encounter as they drive southbound -- apparently the same parts that were compromised in last month's collapse. Similar notes appear in other inspections as well.
In October, a bridge maintenance specialist at DOT notified another official about the large gash in the northbound portion of the bridge and the other damage that appeared to accompany it. Images show how the steel suffered under the impact, with one portion peeling back like a torn piece of paper and left pointing down the roadway. A patch of gray paint is completely gone, exposing some older green paint and the brown metal underneath.
DOT officials decided the damage wasn't severe enough to warrant an emergency, but the department worked to mend the metal and conduct a special inspection of the span.
Washington Sen. Michael Baumgartner, R-Spokane, wants DOT to take a stronger oversight role in oversize vehicle permitting to make sure such hits don't keep happening. He'd like to see the department prohibit vehicles from traveling in areas where their loads might strike overhead portions, and said officials could automatically offer alternative routes to those drivers.
Baumgartner said it was a huge risk to rely solely on the driver to safely navigate the route, especially when it may mean that the driver has to be in a specific lane.
"That's just an unacceptable risk to take," Baumgartner said.
The Skagit bridge is deemed "fracture critical" because it can collapse if a single, vital component of the span is compromised. A preliminary report from the National Transportation Safety Board determined that it failed last month because the impact of the oversize load on the overhead portions of the bridge caused significant damage to those critical elements.
The driver told investigators that he felt "crowded" by another vehicle that was passing him as they arrived at the bridge, so he moved his vehicle to the right.
In order to keep traffic moving, crews opened a temporary replacement for the bridge this week, allowing motorists to cross at a slower speed. The state hopes to have a permanent replacement built in the coming months -- although much of it will remain in its current size and style.
DOT is not allowing oversize loads to travel the temporary Skagit bridge. Phelps said it's not clear if drivers will get a caution statement for the span when the permanent replacement reopens.
"We're going to wait and see what the investigation of the NTSB uncovers," Phelps said.
More Northwest Headlines
State Supreme Court won’t block Eyman anti-tax initiative Court finds Washington charter school law unconstitutional 5:39 p.m. Judge orders Pasco teachers back to school Bail set at $2 million for man accused of wounding officer 5:20 p.m. Fuel spill from Port Orchard vessel more than 500 gallons 5:17 p.m. Anti-California stickers placed on Portland ‘For Sale’ signs Union Gap settles with former clerk for $750,000 Fire ban in state parks lifted in Western Oregon
Our new comment system is not supported in IE 7. Please upgrade your browser here.